free hit counter
Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Albasca Manuals
  4. Barcode Reader
  5. MK-5200
  6. Configuration manual

Albasca MK-5200 Configuration Manual

2d imager barcode scanner
Hide thumbs

Advertisement

Quick Links

Download this manual
MK-5200
2D Imager Barcode Scanner
Configuration Guide
V 1.2

Advertisement

loading

Related Manuals for Albasca MK-5200

Summary of Contents for Albasca MK-5200

  • Page 1 MK-5200 2D Imager Barcode Scanner Configuration Guide V 1.2...
  • Page 2 Programming the Engine Programming the Engine Code Programming On/Off Code Programming ON Read the “Code Programming ON” barcode to activate “Code Program- ming” function. One or more Code Programming barcodes can be read to configure the Engine. If an option or feature needs additional parameters, such as digits, they can be found at the end of this chapter.
  • Page 3 Programming the Engine Programming the Engine Illumination Code Programming ON Illumination LED lighting up barcodes are used to capture better images. There are 4 modes: “Illumination Wink”: LED keeps flashing when reading » Code Programming OFF “Illumination Keep ON”: LED keeps on when Power ON »...
  • Page 4 Programming the Engine Programming the Engine Aiming Code Programming ON There are 3 modes: “Aim Wink”: LED keeps flashing when reading » “Aim Keep ON”: LED keeps on when Power ON » “Aim OFF”: LED is off all the time »...
  • Page 5 Programming the Engine Programming the Engine Beep Code Programming ON Decoding Beep Read “Beep ON” to enable all decoding beep denotation and read “Beep OFF” to disable. Code Programming OFF **Beep ON 【Pro CMD：0203010】 Beep OFF 【Pro CMD：0203000】 Decoding Beep Type **Type 1 【Pro CMD：0203020】...
  • Page 6 Programming the Engine Programming the Engine Beep Code Programming ON Decoding Beep Volume ** Loud Code Programming OFF 【Pro CMD：0203030】 【Pro CMD：0203032】 Medium 【Pro CMD：0203031】 Power On Beep ** Beep On 【Pro CMD：0204001】 Beep OFF 【Pro CMD：0204000】 Beep Denotation (Beeper Definitions) Beep Denotation low-higher-higher-higher...
  • Page 7 Programming the Engine Programming the Engine Reading Mode Code Programming ON Hand-held Mode: Pull and keep holding the trigger line to read. Com- » plete one reading or release the trigger to terminate reading status. Auto Mode: The ambient luminance change in front of the engine auto- »...
  • Page 8 Programming the Engine Programming the Engine Reading Timeout and Delay Code Programming ON One Reading Timeout：If the engine doesn't read any barcode during the timeout period, it will stop reading automatically. One Reading Timeout is valid in Auto mode. The default timeout is 3000ms. Same Barcode Reading Delay：It is used to avoid misreading on the same Code Programming OFF barcode (the same format and message) in a Same Barcode Reading Delay...
  • Page 9 Programming the Engine Programming the Engine Sensitivity Code Programming ON Sensitivity is how sensitive the engine is to ambient illumination change. » Sensitivity value is [1 .. 20] » The lower the sensitivity value is the higher sensitivity will be. The low- »...
  • Page 10 Programming the Engine Programming the Engine Exposure Imaging Mode Code Programming ON Code Programming OFF ** Normal Exposure Mode 【Pro CMD：0321000】 Reflections Eliminating Mode 【Pro CMD：0321010】 Page 9...
  • Page 11 Programming the Engine Programming the Engine Default Code Programming ON Factory Default Read “Load All Factory Default” to reset all parameters to factory default. Applicable conditions: Code Programming OFF User options programming wrong configuration leads to reading mal- » function Forget details of previous programming and start over.

  • Page 12: Usb Interface

    USB Interface Introduction When only data transmission is needed through USB connection, USB HID-KBW option can be programmed. It emulates the unit’s transmission as a USB keyboard input. The Host receives keystrokes of the virtual keyboard. It is “Plug and Play”. There is no driver required. Page 11...
  • Page 13 USB Interface USB Interface USB HID-KBW Code Programming ON USB connection (no driver needed) supports simulating the Imager transmission to be a USB keyboard input. The Host receives keystrokes of the virtual keyboard. It works in “Plug and Play” base. There is no driver required. Code Programming OFF Select USB HID-KBW 【Pro CMD：1100020】...
  • Page 14 USB Interface USB Interface USB HID-KBW Code Programming ON USB Country Keyboard Types The keyboard arrangements and country codes vary in different countries. Refer country codes to the table “USB Country Keyboard Types”. Follow the steps mentioned below to program. Code Programming OFF 1、...
  • Page 15 USB Interface USB HID-KBW Country/Language Number Country/Language Number U.S. Netherlands(Dutch) Belgium Norway Brazil Poland Canada(French) Portugal Czechoslovakia Romania Denmark Russia Finland(Swedish) Slovakia France Spain Germany/Austria Sweden Greece Switzerland(German) Hungary Turkey F Israel(Hebrew) Turkey Q Italy Latin-American Japan Page 14...
  • Page 16 USB Interface USB Interface USB HID-KBW Code Programming ON Unknown Characters, Beep HID-KBW deems an unknown character to be a character is not included in a country keyboard type. It may not be able to allocate and send a keystroke, thus lead to an error beep.
  • Page 17 USB Interface USB Interface USB HID-KBW Code Programming ON Emulate ALT + keypad When enabled, full ASCII characters (0x00～0xff) can be sent over the numeric key- pad regardless country keyboard selections. 1、 “ALT” Make Code Programming OFF 2、 According to the ASCII value, input the numbers over the numeric keypad 3、...
  • Page 18 USB Interface USB Interface USB HID-KBW Code Programming ON Function Key Mapping When enabled, function characters (0x00~0x1F) are sent as ASCII sequences over the numeric keypad. 1、 “Ctrl make” Code Programming OFF 2、 Hit function key 3、 “Ctrl Break” ** No Function Key Mapping 【Pro CMD：1103130】...

  • Page 19: Ascii Function Key Mapping Table

    USB Interface USB HID-KBW ASCII Function Key Mapping Table ASCII Function ASCII Value(HEX) No Function Key Mapping Function Key Mapping Null Crtl+2 Keypad Enter Crtl+A Caps lock Crtl+B Null Crtl+C Null Crtl+D Null Crtl+E Null Crtl+F Enter Crtl+G LeftArrow Crtl+H Crtl+I DownArrow Crtl+J...
  • Page 20 USB Interface USB Interface USB HID-KBW Code Programming ON Keystroke Delay This parameter sets the delay, in milliseconds, between emulated keystrokes. Scan programming code below to increase the delay when the Host require a slower trans- mission of data. Code Programming OFF ** No Delay 【Pro CMD：1103050】...
  • Page 21 USB Interface USB Interface USB HID-KBW Code Programming ON Convert Case The Imager converts all barcode messages to the selected case. Code Programming OFF ** No Case Conversion 【Pro CMD：1103040】 Convert All to Upper Case 【Pro CMD：1103041】 Convert All to Lower Case 【Pro CMD：1103042】...
  • Page 22 USB Interface USB Interface USB HID-KBW Code Programming ON Emulate Numeric Keypad Code Programming OFF When disable, the whole barcode message will be emulated as keystrokes on main keyboard. Read “Emulate Numeric Keypad” to enable the function. when “0~9”is of the barcode message, it will be emulated as keystrokes on numeric keypad.
  • Page 23 USB Interface USB Interface USB COM Port Emulation Code Programming ON When the USB port is connected to Host serial port in order to receive data from scanner, the model of imitating USB-to-RS232 has to be chosen. Hence, the engine and the Host must communicate at the same parameters and the parameters of real serial port and visual serial port must be the same.
  • Page 24 Symbols Introduction This chapter lists all the available symbols and provides the programming barcodes to enable/disable them. Disabling reading of the symbols which do not apply, will improve reading performance. The few abling reading of the symbols are, the fast the engine will work. Page 23...
  • Page 25 Symbols General Options Code Programming ON Disable Reading All Disable Reading All = Allow reading Programming Codes only. Code Programming OFF Disable Reading All 【Pro CMD：0001010】 Enable Reading All Enable Reading All = Enable to read all symbols and Programming Codes. Enable Reading All 【Pro CMD：0001020】...
  • Page 26 Symbols General Options Code Programming ON Enable Reading All 2D Code Programming OFF Enable Reading All 2D 【Pro CMD：0001060】 Disable Reading All 2D Disable Reading All 2D 【Pro CMD：0001050】 Page 25...
  • Page 27 Symbols Code 128 Code Programming ON Load Factory Default Code Programming OFF ** Load Code 128 Factory Default 【Pro CMD：0400000】 Enable/Disable Code 128 Disable Code 128 【Pro CMD：0400010】 ** Enable Code 128 【Pro CMD：0400020】 When the engine can not read Code 128, please read“Enable Code 128” and try again. Page 26...
  • Page 28 Symbols Code 128 Code Programming ON Select Message Length It is used to program the valid reading length of Code 128. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Code 128 Message Length is defined by “Min.
  • Page 29 Symbols EAN-8 Code Programming ON Load Factory Default Code Programming OFF ** Load UCC/EAN-8 Factory Default 【Pro CMD：0401000】 Enable/Disable UCC/EAN-8 ** Enable UCC/EAN-8 【Pro CMD：0401020】 Disable UCC/EAN-8 【Pro CMD：0401010】 Check Digit UCC/EAN-8 is fixed 8 digits barcode and the last digit is check digit. **Transmit Check 【Pro CMD：0401040】...
  • Page 30 Symbols EAN-8 Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code. Picture below shows an ordinary code with a 2 digits Addenda Code. The left one in blue lines is an ordinary code. The right one in red lines is the 2 digits Addenda Code.
  • Page 31 Symbols EAN-8 Code Programming ON EAN-8 expand to EAN-13 Expand EAN-8 to EAN-13, by adding 5 bytes of “0” to the left, and then transmit. Code Programming OFF ** Do Not Expand to EAN-13 【Pro CMD：0401090】 Expand to EAN-13 【Pro CMD：0401100】 Page 30...
  • Page 32 Symbols EAN-13 Code Programming ON Load Factory Default ** Load EAN-13 Factory Default 【Pro CMD：0402000】 Code Programming OFF Disable/EnableEAN-13 ** Enable EAN-13 【Pro CMD：0402020】 Disable EAN-13 【Pro CMD：0402010】 Check Digit ** Transmit Check 【Pro CMD：0402040】 Do Not Transmit Check 【Pro CMD：0402030】 Page 31...
  • Page 33 Symbols EAN-13 Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code. Picture below shows an ordinary code with a 2 digits Addenda Code. The left one in blue lines is an ordinary code. The right one in red lines is the 2 digits Addenda Code.
  • Page 34 Symbols UPC-E Code Programming ON Load Factory Default ** Load UPC-E Factory Default 【Pro CMD：0403000】 Code Programming OFF Disable/Enable UPC-E ** Enable UPC-E 【Pro CMD：0403020】 Disable UPC-E 【Pro CMD：0403010】 When the engine can not read UPC-E, please read “Enable UPC-E” and try again. Check Digit UPC-E is fixed 8 digits barcode and the last digit is check digit.
  • Page 35 Symbols UPC-E Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code. Picture below shows an ordinary code with a 2 digits Addenda Code. The left one in blue lines is an ordinary code. The right one in red lines is the 2 digits Addenda Code.
  • Page 36 Symbols UPC-E Code Programming ON Transmit Default “0” The first byte of UPC-E is default to “0”. Code Programming OFF ** Do Not Transmit “0” 【Pro CMD：0403090】 Transmit “0” 【Pro CMD：0403100】 UPC-E Expand to UPC-A Follow the standard algorithm to expand UPC-E to UPC-A. **Do Not Expand to UPC-A 【Pro CMD：0403110】...
  • Page 37 Symbols UPC-A Code Programming ON Load Factory Default ** Load UPC-A Factory Default 【Pro CMD：0404000】 Code Programming OFF Disable/Enable UPC-A ** Enable UPC-A 【Pro CMD：0404020】 Disable UPC-A 【Pro CMD：0404010】 When the engine can not read UPC-A, please read “Enable UPC-A” and try again. Check Digit UPC-A is fixed 13 digits barcode and the last digit is Check Digit.
  • Page 38 Symbols UPC-A Code Programming ON 2 Digits Addenda Code Addenda Code is the one to the right of an ordinary code. Picture below shows an ordinary code with a 2 digits Addenda Code. The left one in blue lines is an ordinary code. The right one in red lines is the 2 digits Addenda Code.
  • Page 39 Symbols UPC-A Code Programming ON Transmit Default “0” The first byte of UPC-A is default to “0”. Code Programming OFF **Do Not Transmit “0” 【Pro CMD：0404090】 Transmit “0” 【Pro CMD：0404100】 UPC-A has the default “0” but it is not printed out, unlike UPC-E. Read “Transmit 0”...
  • Page 40 Symbols Interleaved 2 of 5 Code Programming ON Load Factory Default Code Programming OFF ** Load Interleaved 2 of 5 Factory Default 【Pro CMD：0405000】 Disable/Enable Interleaved 2 of 5 ** Enable Interleaved 2 of 5 【Pro CMD：0405020】 Disable Interleaved 2 of 5 【Pro CMD：0405010】...
  • Page 41 Symbols Interleaved 2 of 5 Code Programming ON Select Message Length It is used to program the valid reading length of Interleaved 2 of 5. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
  • Page 42 Symbols Interleaved 2 of 5 Code Programming ON Check Digit Interleaved 2 of 5 may include Check Digit (not compulsory) following its barcode messages. It verifies the barcode message. “NO Check, Transmit All” means to read without check and transmit »...
  • Page 43 Symbols Interleaved 2 of 5 Code Programming ON Specified Lengths Program the engine to read specified lengths or ranges of specified lengths for Interleaved 2 of 5. The length value must be 3 decimal digits. And the length value MUST be an even number between 2 to 64. Read “Enable Specified Length”...
  • Page 44 Symbols ITF-14 Code Programming ON ITF-14 is a fixed length, 14 bytes Interleaved 2 of 5 barcode with Check digit. By factory default, it is disabled. When enabled, ITF-14 precedes 14-byte Interleaved 2 of 5 barcode. Code Programming OFF **Disable ITF-14 【Pro CMD：0405080】...
  • Page 45 Symbols ITF-6 Code Programming ON ITF-6 is a fixed length 6 bytes Interleaved 2 of 5 barcode with check digit. When enabled, ITF-6 precedes 6-byte Interleaved 2 of 5 barcode. Code Programming OFF **Disable ITF-6 User Selection 【Pro CMD：0405110】 ITF-6, Read, Do Not Transmit Check Digit 【Pro CMD：0405120】...
  • Page 46 Symbols Code 39 Code Programming ON Load Factory Default Code Programming OFF ** Load Code 39 Factory Default 【Pro CMD：0408000】 Enable/Disable Code 39 ** Enable Code 39 【Pro CMD：0408020】 Disable Code 39 【Pro CMD：0408010】 When the engine can not read Code 39, please read “Enable Code 39” and try again Transmit Start &...
  • Page 47 Symbols Code 39 Code Programming ON Select Message Length It is used to program the valid reading length of Code 39. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Code 39 Message Length is defined by “Min.
  • Page 48 Symbols Code 39 Code Programming ON Check Digit Code 39 may include Check Digit (not compulsory) following its barcode message. It verifies the barcode message. "NO Check, Transmit All" means to read without check and transmit » all bytes including barcode message and Check Digit. Code Programming OFF "Check, Do Not Transmit Check Digit"...
  • Page 49 Symbols Codabar Code Programming ON Load Factory Default Code Programming OFF ** Load Codabar Factory Default 【Pro CMD：0409000】 Enable/Disable Codabar ** Enable Codabar 【Pro CMD：0409020】 Disable Codabar 【Pro CMD：0409010】 When the engine can not read Codabar, please read “Enable Codabar” and try again. Page 48...
  • Page 50 Symbols Codabar Code Programming ON Select Message Length It is used to program the valid reading length of Codabar. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Code Programming OFF Codabar Message Length is defined by “Min.
  • Page 51 Symbols Codabar Code Programming ON Check Digit Codabar may include Check Digit (not compulsory) following its barcode message. It verifies the barcode message. "NO Check, Transmit All" means to read without check and transmit » all bytes including barcode message and Check Digit. Code Programming OFF "Check, Do Not Transmit Check Digit"...
  • Page 52 Symbols Codabar Code Programming ON Transmit Start & Stop Character Codabar uses either one of “A”, “B”, “C” and “D” as the start character and the stop character. Transmission of them can be selected. Code Programming OFF **Transmit Both Start & Stop Character 【Pro CMD：0409090】...
  • Page 53 Symbols Code 93 Code Programming ON Load Factory Default Code Programming OFF ** Load Code 93 Factory Default 【Pro CMD：0410000】 Enable /Disable Code 93 ** Disable Code 93 【Pro CMD：0410010】 Enable Code 93 【Pro CMD：0410020】 When the engine can not read Code 93, please read “Enable Code 93” and try again. Page 52...
  • Page 54 Symbols Code 93 Code Programming ON Select Message Length It is used to program the valid reading length of Code 93. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Code 93 Message Length is defined by “Min.
  • Page 55 Symbols Code 93 Code Programming ON Check Digit Code 93 may include Check Digits (not compulsory) following its barcode message. The two digits verify the barcode message. "NO Check, Transmit All" means to read without check and transmit » all bytes including barcode message and Check Digits. Code Programming OFF "Check, Do Not Transmit Check Digit"...
  • Page 56 Symbols UCC/EAN-128 Code Programming ON Load Factory Default ** Load UCC/EAN-128 Factory Default 【Pro CMD：0412000】 Code Programming OFF Enable/Disable UCC/EAN-128 ** Enable UCC/EAN-128 【Pro CMD：0412020】 Disable UCC/EAN-128 【Pro CMD：0412010】 When the engine can not read UCC/EAN-128, please read “Enable UCC/EAN-128” and try again.
  • Page 57 Symbols GS1 Databar Code Programming ON Load Factory Default Code Programming OFF ** Load GS1 Databar Factory Default 【Pro CMD：0413000】 Enable/Disable GS1 Databar ** Enable GS1 Databar 【Pro CMD：0413020】 Disable GS1 Databar 【Pro CMD：0413010】 When the engine can not read GS1 Databar, please read “Enable GS1 Databar” and try again.
  • Page 58 Symbols EAN·UCC Composite Code Programming ON Load Factory Default Code Programming OFF ** Load EAN·UCC Composite Factory Default 【Pro CMD：0414000】 Enable/Disable EAN·UCC Composite Enable EAN·UCC Composite 【Pro CMD：0414020】 ** Disable EAN·UCC Composite 【Pro CMD：0414010】 Enable UPC/EAN Composite 【Pro CMD：0414040】 ** Disable UPC/EAN Composite 【Pro CMD：0414030】...
  • Page 59 Symbols Code 11 Code Programming ON Load Factory Default Code Programming OFF ** Load Code 11 Factory Default 【Pro CMD：0415000】 Enable/Disable Code 11 Enable Code 11 【Pro CMD：0415020】 ** Disable Code 11 【Pro CMD：0415010】 When the engine can not read Code 11, please read “Enable Code 11” and try again. Page 58...
  • Page 60 Symbols Code 11 Code Programming ON Select Message Length It is used to program the valid reading length of Code 11. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Code 11 Message Length is defined by “Min.
  • Page 61 Symbols Code 11 Code Programming ON Check Digit Code 11 may include Check Digit (not compulsory) following its barcode message. It verifies the barcode message. "NO Check, Transmit All" means to read without check and transmit all » bytes including barcode message and Check Digit. Code Programming OFF "Check, Do Not Transmit Check Digit"...
  • Page 62 Symbols ISBN Code Programming ON Load Factory Default Code Programming OFF ** Load ISBN Factory Default 【Pro CMD：0416000】 Enable/Disable ISBN Enable ISBN 【Pro CMD：0416020】 ** Disable ISBN 【Pro CMD：0416010】 When the engine can not read ISBN, please read “Enable ISBN” and try again. Transmit ** Transmit 13 digits 【Pro CMD：0416030】...
  • Page 63 Symbols Industrial 25 Code Programming ON Load Factory Default Code Programming OFF ** Load Industrial 25 Factory Default 【Pro CMD：0417000】 Enable/Disable Industrial 25 Enable Industrial 25 【Pro CMD：0417020】 ** Disable Industrial 25 【Pro CMD：0417010】 When the engine can not read Industrial 25, please read “Enable Industrial 25” and try again.
  • Page 64 Symbols Industrial 25 Code Programming ON Select Message Length It is used to program the valid reading length of Industrial 25. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Industrial 25 Message Length is defined by “Min.
  • Page 65 Symbols Industrial 25 Code Programming ON Check Digit Industrial 25 may include Check Digit (not compulsory) following its barcode message. It verifies the barcode message. "NO Check, Transmit All" means to read without check and transmit all » bytes including barcode message and Check Digit. Code Programming OFF "Check, Do Not Transmit Check Digit"...
  • Page 66 Symbols Standard 25 Code Programming ON Load Factory Default Code Programming OFF ** Load Standard 25 Factory Default Pro CMD 【 ：0418000】 Enable/Disable Standard 25 Enable Standard 25 【Pro CMD：0418020】 ** Disable Standard 25 【Pro CMD：0418010】 When the engine can not read Standard 25, please read “Enable Standard 25” and try again.
  • Page 67 Symbols Standard 25 Code Programming ON Select Message Length It is used to program the valid reading length of Standard 25. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Standard 25 Message Length is defined by “Min.
  • Page 68 Symbols Standard 25 Code Programming ON Check Digit Standard 25 may include Check Digit (not compulsory) following its barcode message. It verifies the barcode message. "NO Check, Transmit All" means to read without check and transmit all » bytes including barcode message and Check Digit. Code Programming OFF "Check, Do Not Transmit Check Digit"...
  • Page 69 Symbols Plessey Code Programming ON Load Factory Default Code Programming OFF ** Load Plessey Factory Default Pro CMD 【 ：0419000】 Enable/Disable Plessey Enable Plessey 【Pro CMD：0419020】 ** Disable Plessey 【Pro CMD：0419010】 When the engine can not read Plessey, please read “Enable Plessey” and try again. Page 68...
  • Page 70 Symbols Plessey Code Programming ON Select Message Length It is used to program the valid reading length of Plessey. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Plessey Message Length is defined by “Min.
  • Page 71 Symbols Plessey Code Programming ON Check Digit Plessey may include Check Digits (not compulsory) following its barcode message. The two digits verify the barcode message. "NO Check, Transmit All" means to read without check and transmit all » bytes including barcode message and Check Digits. Code Programming OFF "Check, Do Not Transmit Check Digit"...
  • Page 72 Symbols MSI-Plessey Code Programming ON Load Factory Default Code Programming OFF ** Load MSI-Plessey Factory Default Pro CMD 【 ：0420000】 Enable/Disable MSI-Plessey Enable MSI-Plessey 【Pro CMD：0420020】 ** Disable MSI-Plessey 【Pro CMD：0420010】 When the engine can not read MSI-Plessey, please read “Enable MSI-Plessey” and try again.
  • Page 73 Symbols MSI-Plessey Code Programming ON Select Message Length It is used to program the valid reading length of MSI-Plessey. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Code Programming OFF MSI-Plessey Message Length is defined by “Min.
  • Page 74 Symbols MSI-Plessey Code Programming ON Check Digit Plessey may include Check Digits(s) (not compulsory) following its barcode message. It may have one or two digits, which verify the barcode message. "NO Check, Transmit All" means to read without check and transmit all »...
  • Page 75 Symbols PDF417 Code Programming ON Load Factory Default Code Programming OFF ** Load PDF417 Factory 【Pro CMD：0501000】 Enable/Disable PDF417 ** Enable PDF417 【Pro CMD：0501020】 Disable PDF417 【Pro CMD：0501010】 When the engine can not read PDF417, please read “Enable PDF417” and try again. Page 74...
  • Page 76 Symbols PDF417 Code Programming ON Select Message Length It is used to program the valid reading length of PDF417. The engine will not send barcode message to the Host, if the decoded data length does not match the valid reading length. PDF417 Message Length is defined by "Min.
  • Page 77 Symbols PDF417 Code Programming ON PDF417 Twin Code PDF417 twin code is 2 PDF417 barcodes paralleled vertically or horizontally. They must have the same direction. Their specifications must be similar and the distance between them must be short. There are 3 options for reading PDF417 twin code: Code Programming OFF Single PDF417 Only: Read either PDF417 code.
  • Page 78 Symbols QR Code Code Programming ON Load Factory Default Code Programming OFF ** Load QR Code Factory Default 【Pro CMD：0502000】 Enable/Disable QR Code ** Enable QR Code 【Pro CMD：0502020】 Disable QR Code 【Pro CMD：0502010】 When the engine can not read QR Code, please read “Enable QR Code” and try again. Page 77...
  • Page 79 Symbols QR Code Code Programming ON Select Message Length It is used to program the valid reading length of QR Code. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length.
  • Page 80 Symbols QR Code Code Programming ON QR Twin Code QR twin code is 2 QR barcodes paralleled vertically or horizontally.They must have the same direction. Their specifications must be similar and the distance between them must be short. There are 3 options for reading QR twin code: Code Programming OFF Single QR Only: Read either QR code.
  • Page 81 Symbols Aztec Code Programming ON Load Factory Default Code Programming OFF ** Load Aztec Factory Default 【Pro CMD：0503000】 Enable/Disable Aztec Enable Aztec 【Pro CMD：0503020】 ** Disable Aztec 【Pro CMD：0503010】 When the engine can not read Aztec, please read “Enable Aztec” and try again. Page 80...
  • Page 82 Symbols Aztec Code Programming ON Select Message Length It is used to program the valid reading length of Aztec. The engine will not send barcode message to the Host, if the decoded data length does not match the valid length. Aztec Message Length is defined by “Min.
  • Page 83 Symbols Aztec Code Programming ON Reading Multi-barcodes of an Image There are three modes: Mode 1：Read one barcode only. » Code Programming OFF Mode 2：Read fixed number of barcodes only. » Mode 3：Composite Reading. Read fixed number of barcodes first, if failed, »...
  • Page 84 Symbols Aztec Code Programming ON The number of Multi-barcodes Code Programming OFF ** 1 【Pro CMD：0503060】 【Pro CMD：0503064】 【Pro CMD：0503061】 【Pro CMD：0503065】 【Pro CMD：0503062】 【Pro CMD：0503066】 【Pro CMD：0503063】 【Pro CMD：0503067】 Page 83...
  • Page 85 Symbols Data Matrix Code Programming ON Load Factory Default Code Programming OFF ** Load Data Matrix Factory Default 【Pro CMD：0504000】 Enable/Disable Data Matrix ** Enable Data Matrix 【Pro CMD：0504020】 Disable Data Matrix 【Pro CMD：0504010】 When the engine can not read Data Matrix, please read “Enable Data Matrix” and try again.
  • Page 86 Symbols Data Matrix Code Programming ON Select Message Length It is used to program the valid reading length of Data Matrix. The engine will not send barcode message to the Host, if the decoded data length does not match the valid reading length.
  • Page 87 Symbols Data Matrix Code Programming ON Data Matrix Twin Code Data Matrix twin code is 2 Data Matrix barcodes paralleled vertically or horizontally.They must have the same direction. Their specifications must be similar and the distance between them must be short. Code Programming OFF There are 3 options for reading Data Matrix: Single Data Matrix Only: Read either Data Matrix.
  • Page 88 Symbols Data Matrix Code Programming ON Rectangular Symbols Data Matrix has two formats: Square symbols, which has the same amount of models in length and » Code Programming OFF width： 10*10，12*12..144*144。 Rectangular symbols, which has different amounts of models in length and »...
  • Page 89 Symbols Maxicode Code Programming ON Load Factory Default Code Programming OFF ** Load Maxicode Factory Default 【Pro CMD：0505000】 Enable/Disable Maxicode Enable Maxicode 【Pro CMD：0505020】 ** Disable Maxicode 【Pro CMD：0505010】 When the engine can not read Maxicode, please read “Enable Maxicode” and try again. Page 88...
  • Page 90 Symbols Maxicode Code Programming ON Select Message Length It is used to program the valid reading length of Maxicode. The engine will not send barcode message to the Host, if the decoded data length does not match the valid reading length. Maxicode Message Length is defined by "Min.
  • Page 91 Introduction OCR (Optical Character Recognition) is the technology that captures image of printed information, and recognizes the image to editable characters. The engine supports OCR B standard and specific typefaces, such as: ■ 0 1 2 3 4 5 6 7 8 ■...
  • Page 92 Prefix/Suffix Introduction 1D barcodes could contain digits, letters and symbols, etc. 2D barcodes could contain more data, such as Chinese characters and other multi-byte characters. However, in reality, they do not and should not have all the information we need, such as barcode type, date and time of scan, delimiter, and so on, in order to keep the code short and flexible.
  • Page 93 Prefix/Suffix Prefix/Suffix General Programming Code Programming ON Disable or Enable Prefix/Suffix Disable All Prefix/Suffix: Transmit barcode message with no Prefix/Suffix. Enable All Prefix/Suffix: Allow appending Code ID prefix, AIM prefix, User Code Programming OFF prefix, User suffix and Terminal to the barcode message. ** Disable All Prefix/Suffix 【Pro CMD：0311000】...
  • Page 94 Prefix/Suffix Prefix/Suffix General Programming Code Programming ON Prefix Sequences 6 options of Prefix Sequences: Code Programming OFF ** CodeID + AIM + User Prefix 【Pro CMD：0317000】 AIM + User Prefix + CodeID 【Pro CMD：0317030】 CodeID + User Prefix + AIM 【Pro CMD：0317010】...
  • Page 95 Prefix/Suffix Prefix/Suffix General Programming Code Programming ON Disable or Enable User Prefix User Prefix is added before barcode message. For example, if the user prefix is “AB” and the barcode message is “123”, the Host receives “AB123”. Code Programming OFF ** Disable User Prefix 【Pro CMD：0305000】...
  • Page 96 Prefix/Suffix Prefix/Suffix AIM Prefix Tools Code Programming ON AIM (Automatic Identification Manufactures) defines AIM prefix for many standard barcode formats. AIM Prefix Format: “]” + AIM prefix + “0” Code Programming OFF ** Disable AIM Prefix 【Pro CMD：0308000】 Enable AIM Prefix 【Pro CMD：0308030】...
  • Page 97 Prefix/Suffix Prefix/Suffix Code ID Prefix Tools Code Programming ON Besides AIM prefix, Code ID prefix can be used to denote barcode format and can be customized. The Code ID prefix MUST be one (1) or two (2) visible English letters. Code Programming OFF ** No Code ID Prefix 【Pro CMD：0307000】...
  • Page 98 Prefix/Suffix Prefix/Suffix Code ID Prefix Tools Code Programming ON Modify Code ID See the examples below for how to modify a code ID and restore factory default code ID. Modify PDF417 Code ID to be “p” (hex value is 0x70) Code Programming OFF 1.
  • Page 99 Prefix/Suffix Prefix/Suffix Code ID Prefix Tools Code Programming ON Modify EAN-8 【Pro CMD：0004040】 Code Programming OFF Modify EAN-13 【Pro CMD：0004050】 Modify ITF-6 【Pro CMD：0004100】 Modify UPC-E 【Pro CMD：0004060】 Modify Code 39 【Pro CMD：0004130】 Modify UPC-A 【Pro CMD：0004070】 Modify Codabar 【Pro CMD：0004150】 Modify Interleaved 2 of 5 【Pro CMD：0004080】...
  • Page 100 Prefix/Suffix Prefix/Suffix Code ID Prefix Tools Code Programming ON Modify Code 128 【Pro CMD：0004020】 Code Programming OFF Modify ISBN 【Pro CMD：0004240】 Modify UCC/EAN-128 【Pro CMD：0004030】 Modify Industrial 25 【Pro CMD：0004250】 Modify Code 11 【Pro CMD：0004280】 Modify Standard 25 【Pro CMD：0004260】 Modify EAN•UCC Composite 【Pro CMD：0004300】...
  • Page 101 Prefix/Suffix Prefix/Suffix User Suffix Tools Code Programming ON Disable or Enable User Suffix User suffix is appended to the right of barcode message. For example, if user suffix is “AB”, and the barcode message is “123”, The Host receives “123AB”. Code Programming OFF **Disable User Suffix 【Pro CMD：0306000】...
  • Page 102 Prefix/Suffix Prefix/Suffix Terminal Tools Code Programming ON Disable or Enable Terminal “Terminal” is the termination for a string of barcode messages. It can not be formatted like other suffix and prefix. It is fixed to the right and the very end of a barcode transmission.

  • Page 103: Message Interception & Pack

    Message Interception & Pack Introduction Barcode message could divide information into different sections, such as product ID, manufacture ID, and so on. They are important overall. However, at certain situations, some of them are not of interest. This is where message interception comes in. Message interception feature allows transmission of selected section(s).
  • Page 104 Message Interception & Pack Message Interception & Pack Message Interception Tools Code Programming ON Interception Rule No.1: It only intercepts selected symbols’ raw barcode messages and it effects all barcodes of the barcode format. Interception Rule No.2: There are maximum 3 interception options restored in the non-volatile memory.
  • Page 105 Message Interception & Pack Message Interception & Pack Message Interception Tools Code Programming ON Programming 1D Intercept Option When programming 1D intercept option, read digit codes as interception command. The rules is as below： The interception command format of 1D interception command regards »...
  • Page 106 Message Interception & Pack Message Interception & Pack General Programming Tools Code Programming ON Programming 2D Intercept Option When programming 2D intercept option, read digit codes as interception command. The rules is as below： The interception command has two parts, which are barcode type »...
  • Page 107 Message Interception & Pack Message Interception & Pack Message Pack Tools Code Programming ON Introduction Data Pack is for the special requirements of barcode message. There are 3 types of data pack. Data pack effects all data formats, in that be sure to load the default “Disable Pack”...

  • Page 108: Batch Programming

    Batch Programming Tools Introduction Code Programming ON Batch Programming can integrate a programming sequence into one barcode. Batch Programming Rules: 1、 Sub-command is in this format: Programming Command + Parameters 2、 Sub-commands are terminated by semicolons. Note that there is no blank between a sub-command and its terminator semicolon.
  • Page 109 Batch Programming How to build a batch command Batch command can contain many commands. Each command is divided by semicolon. Batch command must be ended with save command. Command structure: command (+ equal mark + setting information) The setting command list is provided below There are 4 setting command modes 1、...
  • Page 110 Batch Programming Produce setting code Make the command list (ended with save command) to a PDF417, QR code or DataMatrix. For example, to produce a batch command means: light Always On, Auto Scan, change delay time to 2 seconds, Disable Fixed Length of I 2 of 5. Firstly find commands as follows 0200030;（light Always On）...
  • Page 111 Batch Programming Batch Programming Use batch setting code Tools Code Programming ON Read “Code Programming ON”, then read “enable batch setting code”, and then read the batch setting code produced just now, finally Read “Code Programming Off” Code Programming OFF Code Programming ON 【Pro CMD：0006010】...
  • Page 112 Appendix Digit Code It is must to be read save after read digit code. 【Pro CMD：0000000】 【Pro CMD：0000040】 【Pro CMD：0000010】 【Pro CMD：0000050】 【Pro CMD：0000020】 【Pro CMD：0000060】 【Pro CMD：0000030】 【Pro CMD：0000070】 Page 111...
  • Page 113 Appendix Digit Code 【Pro CMD：0000080】 【Pro CMD：0000120】 【Pro CMD：0000090】 【Pro CMD：0000130】 【Pro CMD：0000100】 【Pro CMD：0000140】 【Pro CMD：0000110】 【Pro CMD：0000150】 Page 112...
  • Page 114 Appendix Appendix Save and Abort Tools Code Programming ON In order to save the received data “Save” has to be read after data transition completed. If error occurs when reading data, the wrong data can be deleted and the setting up can be done again.. Eg, after a program code is received then ‘1 2 3”...
  • Page 115 Appendix AIM ID List Symbol AIM ID Possible AIM ID Modifiers(m) Code 128 UCC/EAN-128 EAN-8 EAN-13 EAN-13 with Addon UPC-E UPC-E with Addon UPC-A UPC-A with Addon 0,1,3 Interleaved 2 of 5 ITF-6 ITF-14 Code 39 0,1,3,4,5,7 Codabar 0,2,4 Code 93 Code 11 0,1,3 ISBN...
  • Page 116 Appendix Code ID List Symbol Code ID Code 128 UCC/EAN-128 EAN-8 EAN-13 UPC-E UPC-A Interleaved 2 of 5 ITF-6 ITF-14 Code 39 Codabar Code 93 Code 11 GS1 Databar EAN•UCC Composite ISBN Industrial 25 Standard 25 Plessey MSI-Plessey PDF417 QR Code Aztec Data Matrix Maxicode...
  • Page 117 Appendix Symbols ID Number Symbol ID Number Code 128 UCC/EAN-128 EAN-8 EAN-13 UPC-E UPC-A Interleaved 2 OF 5 Code 39 Codabar Code 93 ISBN Industrial25 Standard25 Plessey Code11 MSI-Plessey EAN•UCC Composite GS1 Databar PDF417 QR Code Aztec DataMatrix Maxicode User-Define Code SPEC_OCR_B Page 116...